Maintenance and care of PMI FDIC4010 ball screw
Cleaning: Clean the PMI FDIC4010 ball screw regularly to remove dust, oil and impurities on the surface to prevent these contaminants from entering the ball screw and affecting its performance and life. You can use a clean cloth or brush to clean it, or you can use a special detergent to clean it.
Lubrication: The PMI FDIC4010 ball screw needs to be lubricated regularly to reduce friction and wear and improve its transmission efficiency and life. You can use special lubricating oil or grease for lubrication, and choose the appropriate lubricant according to different application scenarios and working conditions.
Inspection: Regularly check the operating status of the PMI FDIC4010 ball screw, including the wear of the ball, the clearance between the screw and the nut, and the lubrication condition. If any problems are found, repair or replace parts in time.
Installation and commissioning: Correct installation and commissioning of the PMI FDIC4010 ball screw is essential for its performance and life. During installation, ensure that the axes of the screw and nut are parallel, the ball is installed in the correct direction, and the tightening torque meets the requirements. During commissioning, no-load and load tests should be performed to check the operation and accuracy of the ball screw.
| SCREWSIZE | BALL DIA. |
EFFECTIVE TURNS |
BASIC RATE LOAD(kg/ | NUT | FLANGE | FIT | BOLT | OIL HOLE |
STFFNESS kg4m |
|||||||||
| QD | LEAD | Dynamic (1×10°REV) Ca |
Static Co |
Dg6 | L | A | T | W | G | H | S | X | Y | Z | Q | |||
| 40.00 | 5.00 | 3.18 | 4 5 6 |
1575 1910 2230 |
5290 6610 7940 |
55.00 | 96 111 122 |
88.50 | 16.00 | 72.00 | 29.00 | 58.00 | 15.00 | 9.00 | 14.00 | 8.50 | M8×1P | 100 124 147 |
| 6.00 | 3.97 | 3 4 6 |
1660 2130 3020 |
4810 6410 9620 |
55.00 | 97 113 137 |
88.50 | 16.00 | 72.00 | 34.00 | 68.00 | 15.00 | 9.00 | 14.00 | 8.50 | M8×1P | 77 103 149 |
|
| 8.00 | 4.76 | 3 4 6 |
2120 2720 3850 |
5720 7620 11430 |
60.00 | 121 134 172 |
93.00 | 16.00 | 76.00 | 36.00 | 72.00 | 20.00 | 9.00 | 14.00 | 8.50 | M8×1P | 80 105 154 |
|
| 10.00 | 6.35 | 3 4 5 |
3010 3850 4670 |
7100 9470 11830 |
64.00 | 142 162 189 |
106.00 | 18.00 | 84.00 | 43.00 | 86.00 | 20.00 | 11.00 | 17.50 | 11.00 | M8×1P | 82 107 133 |
|
| 12.00 | 6.35 | 3 5 |
3010 4670 |
7100 11830 |
63.00 | 154 204 |
106.00 | 18.00 | 84.00 | 43.00 | 86.00 | 20.00 | 11.00 | 17.50 | 11.00 | M8×1P | 82 133 |
|
| 7.14 | 3 4 |
4010 5130 |
9250 12330 |
70.00 | 160 185 |
85.00 | 45.00 | 90.00 | 20.00 | 11.00 | 17.50 | 11.00 | M8x1P | 86 114 |
||||
| 45.00 | 84.76 | 4.00 | 2870 8620 | 64 136 92 3672 15 14.59 M6x1P 109 | ||||||||||||||
| 127.14 | 3 4 |
4160 5330 |
10750 14330 |
70.00 | 158 183 |
11016.00 | 90.00 | 4590201117.511 PT1/8″ | 94 124 |
|||||||||
| 166.35 | 3 3220 8200 70 19811016 904590201117.511 PT1/8″ 90 | |||||||||||||||||
Subscribe to our newsletter for daily new and updates
Shanghai, China
YOSOmachinery
Copyright © Jingpeng Machinery&Equipment(Shanghai) Co.,Ltd All Rights Reserved
EN
AR
BG
CS
DA
NL
FI
FR
DE
EL
HI
IT
JA
KO
NO
PL
PT
RU
ES
SV
TL
ID
UK
VI
HU
TH
TR
FA
AF
MS
SW
GA
CY
BE
KA
LA
MY
TG
UZ
